Molecular aligned Polypropylene mesh. Providing an excellent strength to weight ratio. Nominal hole size 25mm x 25mm Colour Black. 2 Meters wide
Subtotal £3.49
V.A.T @ 20.0% £0.70
Total £4.19 / Meter
SafaMesh6
SafaMesh 6 Nominal hole size 6mm x 7mm.
Molecular aligned Polypropylene mesh. Providing an excellent strength to weight ratio.Nominal hole size 6mm x 7mm Colour Black. 2 meters wide
Subtotal £3.49
V.A.T @ 20.0% £0.70
Total £4.19 / Meter
SafaMeshTie
SafaMesh cable tie to secure the SafaMesh to the SafaDeck..
SafaMesh cable tie to secure the SafaMesh to the SafaDeck. Length 100mm. Pack of 100
Subtotal £3.50
V.A.T @ 20.0% £0.70
Total £4.20 / Pack
SP01-PK50
SP01 Beam Clip Pack Qty 50.
The beam clip is used to clip the grid to the beam. Normally one beam clip is located in each corner of the grid, meaning on average 4 beam clips are required for each grid. Beam clips are also placed over any join in the beams.
Subtotal £20.00
V.A.T @ 20.0% £4.00
Total £24.00 / Pack
SP02-PK50
SP02 Cut End Bumper Pack 50.
The cut end bumper is used to protect butyl and PVC liners from any cut sections of grid. It has a smooth curved side and an open side. The open side has a wider base and a narrower top. It is used in an upside-down position when placing over the diagonal cut sections of grid. It is used in the normal position (opposite) on thicker cross pieces.
Subtotal £20.00
V.A.T @ 20.0% £4.00
Total £24.00 / Pack
SP03-PK50
SP03 Cut End Support Pack 50.
The cut end support is used in the rare event when a section of grid cannot be adequately supported by beams on either side. It is placed over a section of grid and a length of support cord is passed through the bottom two holes which is then anchored outside the pond using either a stake of a ceiling anchor. Ensure the support cord is taught.
Subtotal £20.00
V.A.T @ 20.0% £4.00
Total £24.00 / Pack
SP04-PK25
SP04 Floating Beam Clip Pack 25.
The floating beam clip is used to attach grids to the first and last beams in the pond. It can be used over the ‘star’ configuration in the grid. It is also used to attach any additional support beams to the underside of the grid if required. It is clipped into position using a flat screwdriver – the two curved sections at the base of the clip are clipped into place under the flanged section of the upper part of the beam.
Subtotal £12.50
V.A.T @ 20.0% £2.50
Total £15.00 / Pack
SP05-PK50
SP05 Grid to Grid Clip Pack 50.
The grid to grid clip brings together one grid in a lane with its neighbouring grid. They work in pairs and are clipped in between the tabs on the underside of the grid. One grid to grid clip is placed in one direction, the other in the pair in the other direction. When combined in this way, they draw the two grids together ensuring no separation.
Subtotal £20.00
V.A.T @ 20.0% £4.00
Total £24.00 / Pack
SP06-PK25
SP06 Beam Cleat Pack 25.
The beam cleat is used to cap off the end of the support beam. After the beam is cut to length, without the beam cleat it would pose a threat to the pond liner. The beam cleat has a central hole, through which the support cord is passed.
Subtotal £12.50
V.A.T @ 20.0% £2.50
Total £15.00 / Pack
SP07-PK10
SP07 Foot Pack 10.
The foot is inserted into the bottom of the leg section and rests on the base of the pond. Watch for stones and other sharp objects between the underside of the foot and the liner. The leg is attached to the foot by gently forcing the leg down upon the top of the foot and simultaneously turning the leg until it is in position.
